 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| ISO-9001 CERTIFIED BY DSCC M.S.KENNEDY CORP. FEATURES: 600V/450A HALF BRIDGE PEM 4800 (315) 701-6751 4707 Dey Road Liverpool, N.Y. 13088 MIL-PRF-38534 CERTIFIED Half Bridge Configuration 600V Rated Voltage 450A Continuous Output Current Internal Zener Clamps on Gates Proprietary Encapsulation Provides Near Hermetic Performance MIL-PRF-38534 Screening Available (Modified) Light Weight Domed ALSIC Baseplate Robust Mechanical Design for Hi-Rel Applications Ultra-Low Inductance Internal Layout Withstands 96 Hours HAST and Thermal Cycling (-55C to +125C) High Side Collector Sense Pin for De-Sat Detection DESCRIPTION: The MSK 4800 is one of a family of plastic encapsulated modules (PEM) developed specifically for use in military, aerospace and other severe environment applications. The half bridge configuration and 600 volt/450 amp rating make it ideal for use in high current motor drive and inverter applications. The Aluminum Silicon Carbide (AlSiC) baseplate offers superior flatness and light weight; far better than the copper or copper alloys found in most high power plastic modules. The high thermal conductivity materials used to construct the MSK 4800 allow high power outputs at elevated baseplate temperatures. Our proprietary coating, SEESTM - Severe Environment Encapsulation System - protects the internal circuitry of MSK PEM's from moisture and contamination, allowing them to pass the rugged environmental screening requirements of military and aerospace applications. MSK PEM's are also available with industry standard silicone gel coatings for a lower cost option. EQUIVALENT SCHEMATIC TYPICAL APPLICATIONS Motor Drives Inverters 1 Rev. D 11/05 ABSOLUTE MAXIMUM RATING 8 ELECTRICAL SPECIFICATIONS NOTES: Guaranteed by design but not tested. Typical parameters are representative of actual device performance but are for reference only. Industrial grade and "E" suffix devices shall be tested to subgroup 1 unless otherwise specified. Military grade devices ("H" suffix) shall be 100% tested to subgroups 1, 2 and 3. Subgroups 4, 5 and 6 testing available upon request. Subgroup 1, 4 TA = +25C 2, 5 TA = +125C 3, 6 TA = -55C 6 All specifications apply to both the upper and lower sections of the half bridge. 7 VGE=15V unless otherwise specified. 8 Continuous operation at or above absolute maximum ratings may adversly effect the device performance and/or life cycle 1 2 3 4 5 2 Rev. D 11/05 VCE VGE IOUT IOUTP VCASE Collector to Emitter Voltage Gate to Emitter Voltage Current (Continuous) Current Pulsed (1mS) Case Isolation Voltage 600V 20V 450A 900A 2500 V TST TJ TC -55C to +125C Storage Temperature Range 150C Junction Temperature Case Operating Temperature Range -55C to +125C MSK 4800H/E -40C to +85C MSK 4800 TYPICAL PERFORMANCE CURVES 3 Rev. D 11/05 SCREENING CHART 4 Rev. D 11/05 MECHANICAL SPECIFICATIONS WEIGHT = 272 GRAMS MAX. ORDERING INFORMATION MSK4800 H SCREENING BLANK=INDUSTRIAL; E=EXTENDED RELIABILITY; H=MIL-PRF-38534 CLASS H (MODIFIED) GENERAL PART NUMBER THE ABOVE EXAMPLE IS A MILITARY SCREENED MODULE. M.S. Kennedy Corp. 4707 Dey Road Liverpool, New York 13088 Phone (315) 701-6751 FAX (315) 701-6752 www.mskennedy.com The information contained herein is believed to be accurate at the time of printing. MSK reserves the right to make changes to its products or specifications without notice, however, and assumes no liability for the use of its products. Please visit our website for the most recent revision of this datasheet. 5 Rev. D 11/05 |
Price & Availability of MSK4800H
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |